Skip to content
ApplianceFaults
Search

Error code

Hotpoint Tumble Dryer F07 — Check the Model

The component meaning of F07 has not been confirmed for your Hotpoint dryer. Record the full display and exact model. Before any restart, check whether an older vented or condenser dryer needs recall action; cleaning or clearing a code does not prove it is safe.

Last updated: 7 October 2026

Quick answer

F07: Component meaning unconfirmed; check model and recall status

SeverityNot established

Meaning

Component meaning unconfirmed; check model and recall status

First safe check

Record the full display from an existing photo or note. Do not run another cycle just to reproduce the warning.

Stop if

The dryer is affected by the older-dryer safety programme and its required modification or replacement is not complete.

Who to call

Contact Hotpoint if recall status is uncertain or the dryer is affected and unmodified. For a persistent or unexplained F07 display, use Hotpoint support or a qualified appliance technician; routine cleaning cannot establish a safe repair.

The code meaning and severity have not been established. Confirm the model and manufacturer guidance before attempting a remedy. Follow the model’s isolation instructions before permitted maintenance. Do not reach wet or damaged electrical parts to unplug the appliance.

What does this error code mean?

No component definition for F07 has been established for this page. Match the complete display, including leading zeros or alternating characters, to the exact model and its applicable manual.

Hotpoint's AQCF 852 BI / AQCF 852 BU UK instruction booklet 19507244407_UK, page 17, describes an F display followed by one or two numbers. Apart from its F10/F15 maintenance advice, it tells owners to record the number and contact service. That general instruction does not establish a definition for F07 or prove that this exact display is used on every model.

The UK recall concerns affected vented and condenser dryers made between 1 April 2004 and 30 September 2015, except those modified or replaced under the programme. Check the full model, serial number and modification history using the manufacturer. An affected, unmodified dryer must stay unplugged and unused until the safety action is completed. A fault code, its disappearance or routine cleaning cannot establish recall clearance.

The code and the individual dryer's recall status are separate questions. This evidence gap does not prove that the code is invalid or unused. Do not diagnose a failed part, buy a replacement component or invent a reset sequence from the number alone.

What still needs confirming?

  1. No component cause has been established from the manufacturer evidence reviewed.

What to do next

  1. Record the full display from an existing photo or note. Do not run another cycle just to reproduce the warning.
  2. Find the full model and serial number in accessible paperwork or on an external label; do not dismantle or move the dryer to reach a label unsafely.
  3. Before any restart, use the manufacturer's dryer safety checker to establish whether an older dryer is affected and whether its required modification or replacement is complete. If that status cannot be established, keep it off and ask Hotpoint to confirm.
  4. If the dryer is affected and unmodified, unplug it only if the plug is safely accessible and keep it unused until the manufacturer completes the required safety action.
  5. Give Hotpoint the exact model, serial number and full code. Ask for its applicable definition and instructions before attempting a reset or repair.
  6. If the warning remains or the next step needs internal access, stop and contact Hotpoint support or a qualified appliance technician.

Can I fix this myself?

No

A component repair is not established. Confirm the exact code/model and any required recall action before considering a restart.

Safety boundary: No internal access, electrical testing, protective-device bypass or test cycle to reproduce the fault. Affected, unmodified dryers must remain unused.

What not to do

  1. Do not remove panels, test wiring or bypass a protective device.
  2. Do not use an old manual restart instruction to override a recall warning.
  3. Do not treat a cleared code, clean filter or unrelated model-checker result as proof that the individual dryer is safe.
  4. Do not buy a heater, sensor, motor or control board solely from this display.

When to call a technician

Contact Hotpoint if recall status is uncertain or the dryer is affected and unmodified. For a persistent or unexplained F07 display, use Hotpoint support or a qualified appliance technician; routine cleaning cannot establish a safe repair.

Safety warning

Keep an affected, unmodified recalled dryer unplugged and unused. Stop for smoke, a burning smell, unusual heat, leakage or electrical tripping. Do not touch wet or hot electrical connections, remove panels, test wiring or bypass protection. Do not restart solely because the code has cleared.

Useful hub links

Other Hotpoint tumble dryer codes

Relevant guide

Frequently asked questions

Does F07 identify a failed part?+

No failed component has been established for this page. The exact model and applicable diagnostic definition are still required.

Does this apply to every model?+

No. The owner-guide context is limited to the named AQCF 852 BI / AQCF 852 BU UK models and document revision. It does not establish a component definition for other dryers.

Does clearing the code or cleaning the filter clear a recall?+

No. For affected older dryers, the manufacturer must establish whether the required modification or replacement is complete. Affected, unmodified dryers must stay unplugged and unused.

Sources and review status

Code meaning not yet confirmed · Last reviewed 7 October 2026

in review
  • Hotpoint dryer landing page — appliance mismatch noted

    manufacturer support · UK · checked 21 September 2026

    Material reviewed and limitation: The official dryer landing page contains a washing-machine table, including washer-dryer-only and top-loader-only entries. It is not adequate evidence for a standalone tumble-dryer component diagnosis. This is not confirmation of a component diagnosis.

  • Hotpoint AQCF 852 BI / AQCF 852 BU UK instruction booklet 19507244407_UK, page 17

    model manual · UK · checked 7 October 2026

    Hotpoint's AQCF 852 BI / AQCF 852 BU UK instruction booklet 19507244407_UK, page 17, describes an F display followed by one or two numbers. Apart from its F10/F15 maintenance advice, it tells owners to record the number and contact service. That general instruction does not establish a definition for F07 or prove that this exact display is used on every model.

  • OPSS UK unmodified tumble-dryer recall scope, 10 July 2019

    government safety · UK · checked 7 October 2026

    The UK recall concerns affected vented and condenser dryers made between 1 April 2004 and 30 September 2015, except those modified or replaced under the programme. Check the full model, serial number and modification history using the manufacturer. An affected, unmodified dryer must stay unplugged and unused until the safety action is completed. A fault code, its disappearance or routine cleaning cannot establish recall clearance.

  • Manufacturer dryer safety notice and model checker

    manufacturer support · UK · checked 7 October 2026

    Current notice identifies a lint/heating-element fire concern in some dryers made April 2004 to September 2015 and directs owners to check the model. Affected dryers must not be used before modification; already modified or replacement machines are treated separately. This does not identify the cause of a numbered fault or certify an individual dryer.